TEF1109P-8-63W has the network extension technology. Based on the original twisted pair, it can support up to 250 meters long distance transmission, breaking the hundred meters transfer limit. With 6KV lightning protection, it is the real monitoring private switch. Ports 1-8 support IEEE 802.3at and IEEE 802.3af PoE standard. It provides a maximum PoE output power of 30W to each port and 58W to the whole device.

TEF1105P-4-63W is a Tenda PoE switch that offers 5 10/100 Mbps Base-TX RJ45 ports. Up to 250 meters long distance transmission, beyond hundred meters transfer limit. 6KV lightning protection PoE switch is the real monitoring private switch. Ports 1-4 support IEEE 802.3at and IEEE 802.3af PoE standard. It provides 30W maximum PoE output a single port and 58W the whole device.

Passive PoE Adapter Powers TP-Link products that support 48V passive PoE Power Your Devices Use the passive PoE adapter TL-POE4824 to simultaneously supply power and transmit data to a passive PoE device. Convenient Wall-Mounting Design TL-POE4824 offers a convenient wall-mounting brackets to be easily installed on a wall.

Passive PoE Adapter Powers TP-Link products that support 24V passive PoE TL-POE2412G Power Your Devices Use the passive PoE adapter TL-POE2412G to simultaneously supply power and transmit data to a passive PoE device. Convenient Wall-Mounting Design TL-POE2412G offers a convenient wall-mounting brackets to be easily installed on a wall. Compatible Devices TL-POE2412G is the recommended power supply for compatible devices.

The DPE-301GS PoE splitter is used with end devices such as wireless access points, IP cameras and VoIP phones that don’t natively support PoE, but rather require DC power input of 5V, 9V or 12V. It receives PoE power on a network cable from a PoE switch or midspan injector, and splits the Ethernet and DC power into two separate cables. One cable provides the DC power, and the other cable provides the Ethernet signal. Users can select from 5VDC, 9VDC and 12VDC power for their device using a selectable DIP switch on the device. The DPE-301GS PoE splitter is typically located near the end device. It has two 10/100/1000 RJ-45 ports. One port is for PoE IN, which is the network connection and is usually connected to a remote PoE switch or injector. The other port is for LAN OUT, which is the connection that provides the Ethernet signal to the end device. The DPE-301GS also has a 5.5mm DC OUT port. Two adapter cables are supplied; either one may be connected to this port, depending on whether 5.5mm or 3.8mm interface is required for the end device.

The PoE Splitter TL-POE10R
Fully complies with IEEE 802.3af standard, and can work with all IEEE 802.3af PoE compliant PSE (Power Source Equipment) or PoE Supplier Adapter, such as TP-LINK's TL-SF1008P or TL-POE150S, or other equivalent product, to deliver 12V, 9V or 5V Direct Current to where there are no power line or outlet, where you wish to fix device such as AP, IP Camera or IP Phone, etc.

The PoE Injector TL-POE150S
Fully complies with IEEE 802.3af standard, and can work with all IEEE 802.3af PoE compliant PDs (Powered Devices) or PoE Receiver Adapters, such as TP-LINK’s TL-POE10R, or other equivalent product, to expand your network to where there are no power line or outlet, where you wish to fix device such as AP, IP Camera or IP Phone, etc.

VIVOTEK AP-FIC-010A-015. Ethernet interface type: Fast Ethernet, Networking standards: IEEE 802.3af,IEEE 802.3u, Cable standard: Cat5. Product colour: Black, LED indicators: PoE,Power, Power protection features: Over current,Short circuit. Power over Ethernet (PoE) voltage: 54 V, Output power: 15.4 W, AC adapter input voltage: 100 - 240 V

Key Features
Support 4 additional modes, AI VLAN, AI Extend, AI PoE and AI QoS

• AI Extend: support 250 Meters distance power supply (recommended Cat5e or 6 network cable) @ 10Mbps
• AI VLAN: Isolating ports 1-8 . Each port effectively suppress network storms and improve network performance.
• AI QoS: Prioritize identified video data to make video transmission smoother
• AI POE: Automatically detect the power receiving port, find the dead device, power off and restart the device.

Port Configuration
10M/100M/1G RJ45 Ports: 8
1G Uplink Ports:  --
1G SFP Ports:  2
Total Ports:  10
 
PoE Function 
IEEE802.3at (PoE+ 30W):  Y (46W)
IEEE802.3af (PoE 15.4W):  Y
PoE+ Port:  8
Available PoE Power:  150W
 
HW Performance 
Switching Bandwidth:  20 Gbps
MAC Address:  16k
 
Environmental Specification 
Operating Temperature:  0°C to 40°C
Operating Humidity:  10% to 90% non-condensing
Storage Temperature:  -10°C to 70°C
Storage Humidity:  5% to 90% non-condensing
 
Mechanical Specification 
Dimensions (H) x (W) x (D) mm:  44 x 180 x 285
Weight:  2.05kg
 
Power Source 
AC Input:  100-240V
 

Duxbury 8-port Gigabit PoE+ Unmanaged Switch with 2x Gigabit SFP/Uplink Combo ports DUX1012P

The Duxbury 8-port Gigabit PoE+ Unmanaged Switch with 2x Gigabit SFP/Uplink Combo ports DUX1012P is a powerful and versatile networking device designed for small to medium-sized businesses. This switch offers reliable and efficient connectivity for multiple devices in your network, such as IP cameras, access points, and VoIP phones.

With eight Gigabit PoE+ ports and two Gigabit SFP/Uplink Combo ports, this switch enables you to connect up to eight PoE-enabled devices and two non-PoE devices simultaneously.

The Duxbury DUX1012P is an unmanaged switch, which means that it is easy to install and requires no configuration. The switch also features plug-and-play functionality, which means that you can start using it right out of the box without any additional setup.

In addition to its performance and ease of use, the DUX1012P also features a compact design that is perfect for small offices or home networks. It is built to last, with a sturdy metal housing that protects the switch from accidental damage.

Overall, the Duxbury 8-port Gigabit PoE+ Unmanaged Switch with 2x Gigabit SFP/Uplink Combo ports DUX1012P is an ideal networking device for small to medium-sized businesses that need reliable and efficient connectivity for multiple devices. Its PoE+ capabilities and plug-and-play functionality make it a versatile and cost-effective solution for powering and connecting your network devices.

Technical Specifications
Product: Duxbury 8-port Gigabit PoE+ Switch with 2x Gigabit SFP/Uplink Combo ports
Switch Type: Unmanaged Desktop Switch
Interfaces: 8-port PoE+ Gigabit, 2-port Gigabit SFP, 2-port Gigabit (Combo) Uplink
Total PoE budget: 120W
PoE Digital Display: Yes
AI Mode support 4 additional modes:

• AI VLAN
• AI Extend
• AI PoE

Duxbury 8-port Unmanaged Gigabit Switch

The DUX108G is an unmanaged gigabit Ethernet switch with 8 100/1000Mbps auto-negotiation RJ45 ports, Wire-speed forwarding rate of each port full up to 1000Mbps. It supports lower power consumption, and lightning proof level is up to 4KV to ensure network performance stability and safety when you surf the internet.

With innovative energy-efficient technology design, the DUX108G can save up to 40% of the power consumption, to make it an eco-green solution for your home and office network

• 8 x 10/100/1000BASE-T RJ45 ports, auto MDI/MDIX
• Metal Shell design with Energy-efficient technology
• Plug and play without configuration
• Compliant with IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3ab
• Provides 16Gbps switching bandwidth and non-blocking wire-speed forwarding
• Supports IEEE802.3x full duplex flow control and half duplex backpressure flow control

Duxbury AI 26 Port Layer 2 Managed Gbe PoE+ Switch

• 24-port PoE+ Gigabit Ports x  2 Gig SFP port Switch.
• 250W Total PoE budget.  
• AI Mode support 4 additional modes,
• AI VLAN
• AI Extend
• AI PoE  
• AI QoS
• Layer 2 features provide easier manageability, basic security and QoS
• PoE Port configuration and scheduling
• IEEE 802.3af/at Power over Ethernet  
• IEEE 802.3az EEE Energy Efficient Ethernet standard for green Ethernet
• Rackmount
• 4kV Surge protection per port.

DUX104GPS-2F-IS - 6-port Gigabit managed industrial PoE switch

• 4 Gigabit PoE+ ports and 2 Gigabit SFP ports
• Support IEEE802.3af/at, single port output maximum power 46W
• L2 Managed
• RUN-Ring technology Ring network
• 48-56V DC redundant dual supply voltage input, DIN Rail Support
• Support reverse connection protection, over current protection
• IP40 level protection
• Operating temperature:-40~ 75°C
• 4 AI Modes

• Support 4 additional modes, AI VLAN, AI Extend, AI PoE and AI QoS
• AI Extend: support 250 Meters distance power supply (recommended Cat5e or 6 network cable) @ 10Mbps.
• AI VLAN: Isolating ports 1-8 . Each port effectively suppress network storms and improve network performance.
• AI QoS: Prioritize identified video data to make video transmission smoother.
• AI POE: Automatically detect the power receiving port, find the dead device, power off and restart the device

The Duxbury switches are targeted at applications in small businesses and home offices requiring the installation of Power-over-Ethernet (PoE) devices, such as IP phones, IP cameras and access points. The Duxbury range will keep on expanding to meet the need for specialised, value-added products as well as the volume distribution of its market-leading offerings.

The switches from Duxbury not only represent an easy and cost-effective way to add more Ethernet ports to a small network, they also give users an opportunity to leverage the full potential of increasingly popular IP-based networking solutions - such as security systems - at a budget price.

Key Features:

AI Extend: support 250 Meters distance power supply (recommended Cat5e or 6 network cable) @ 10Mbps
Port Configuration
10M/100M/1G RJ45 Ports: 8
1G Uplink Ports: 2
1G SFP Ports: --
Total Ports: 10

PoE Function
IEEE802.3at (PoE+ 30W): Y
IEEE802.3af (PoE 15.4W): Y
PoE+ Port: 8
Available PoE Power: 96W

HW Performance
Switching Bandwidth: 20 Gbps
MAC Address: 2k

Environmental Specification
Operating Temperature: 0°C to 40°C
Operating Humidity: 10% to 90% non-condensing
Storage Temperature: -10°C to 70°C
Storage Humidity: 5% to 90% non-condensing

Mechanical Specification
Dimensions (H) x (W) x (D) mm: 27 x 94 x 184
Weight: 1.05kg

Power Source
AC Input: 100-240V

What It Does PoE30G-AT PoE Injector delivers up to 30W output power per port. By using this device, both data and electrical power can be simultaneously delivered through a single CAT5 (or better) Ethernet cable to a non-PoE Ethernet-enabled device, eliminating the trouble to connect it to an outlet nearby with an external power cord. You can connect it to a wireless AP, Web cam (IP Camera), IP telephone, or other devices for the purpose of reducing installation cost and improving your network performance. PoE Feature: - Support IEEE802.3af, IEEE802.3at standard; - Auto-detects and provide power supply to PD equipment which compliant with IEEE802.3af at standard; - Power consumption one port up to 30W. Interface Features: - Compliant with IEEE802.3,IEEE802.3u,IEEE802.3ab,IEEE802.3af,IEEE802.3at Ethernet standard; - 2 RJ-45 Gigabit ports support 10/100/1000Mbps connecting rate; - Date&Power Out port support PoE. Product Features: - Integrated design and easy installation; - Plug and play, no need to setup; - GE transmission rate for wide use. Fireproofing Features: - Fireproofing level of case up to 94V0.

PoE15F can realize the synchronous transmission of network data and power through an Ethernet cable (Cat.5 or better). The output power of each port is as high as 15W, which can be exported as PoE equipment (via RJ45 port)

Delivers power and data through one Ethernet cable for easy network extension
Compatible with IEEE 802.3af compliant powered devices
PoE Port Delivers power up to 100 meters
Plug and Play, no configuration required

- Facilitates deployment of PoE devices where power outlets are not available - Reduces installation and network equipment costs by eliminating the need for electrical wiring - Provides power over existing network cabling to PoE devices such as access points, IP cameras, and IP phones - Lightweight, compact and easy to install - Supports 802.3af / 802.3at - 10/100/1000 interface provides flexibility for all types of connections D-Link’s DPE-301GI 1-Port PoE Injector is used to provide I.T. Professionals with the benefits of Power over Ethernet (PoE), even when other devices in the network do not support it. With PoE technology, low voltage DC power and Ethernet data signals are combined on a single network cable, which facilitates powering of end devices like IP Cameras, wireless Access Points (APs), and VoIP Phones. This reduces cable clutter, eliminates the need for dedicated electrical outlets on the wall, ceiling, or other unreachable places, reduces installation time, and lowers costs. The DPE-301GI device supports Gigabit speeds, and can connect to 10Mbps, 100Mbps or 1000Mbps through the RJ-45 interface. This device also supports the IEEE 802.3af and 802.3at PoE/PoE+ standards, which ensures interoperability with other standards-based PoE and PoE+ devices. Small and compact, the DPE-301GI is lightweight, has integrated mounting slots, and is easy to install. The DPE-301GI provides a power and data connection to a PoE device over a single network cable. It allows I.T. Professionals to mount their PoE devices virtually anywhere in a building, such as on ceilings or near entryways, and eliminates the need for nearby power outlets and attached power supplies. The DPE-301GI combines electrical power with a Gigabit network connection and produces a Gigabit PoE signal, allowing a single Ethernet cable to carry both data and power to a device. Also known as a “midspan PSE”, the DPE-301GI PoE injector can be used when deploying a multi-port PoE switch is impractical or not feasible. It has two 10/100/1000 RJ-45 ports. One port is for LAN IN, which is the network connection,typically connected to a non-PoE switch or router. The other port isfor PoE OUT, which is the connection that provides both power and data signal to the end device (PD). The DPE-301GI can be located anywhere on the Ethernet link, although it’s typically placed near the switch/router. Location of the injector does not impact the maximum 100m (328ft.) distance from the switch/router to the end device. Support for IEEE 802.3at ensures the DPE-301GI can power PoE+ devices up to 30W, such as high power 802.11ac APs and IP cameras with PTZ motors, heaters and blowers. PoE Injector and PoE Splitter Tandem Both the DPE-301GI (injector) and DPE-301GS (splitter) can be used together, as a complete PoE transport system. This is especially useful when a PoE switch is not available, and the end device is not PoE capable, but the Network Administrator still prefers the benefits of PoE. Simply install the injector close to the network switch, install the splitter close to the end device, and plug in the cables.