Canting is a pen-like tool used to apply liquid hot wax

Felt Matt for the Smaller Fome School Etching Press which has a width of 180mm. Read our series of blog posts about setting up and using the Fome School Etching Press. Fome Presses available here. Size: 18.6 x 32 x 0.3 cm.

Japanese synthetic waterstones and slipstones for sharpening lino and woodcut tools of all types.

The 4000 grit or fine stone is used for the final hone and polish and will leave the tool ready for use.

Before use the stones will need to be soaked in water for 10 to 15 minutes. After use the stones are best air dried and wrapped in a soft loth for storage.

Well engineered portable presses from Italy with solid steel rollers and 3mm thick metal bed. Lifting up the top roller is for relief printing only, you will not be able to print anything but thinner intaglio plates on this press, optimally up to 1mm metal with a decent bevel on or thinner 0.8mm plates like our econimy zinc or transparent printing plates. The Fome presses work well for line etching, drypoint, monoprint and relief.It must be stressed that these small press will not print with the same pressure as a larger heavier studio press. If you have designed your prints with your plates, inks, paper using a large heavy press, you will not necessarily be able to reproduce them on these small presses. Putting too much pressure on the presses can damage them.Please Note: The manufacturer recommends attaching this press to a table so you can get enough leverage for proper printing function.SpecificationsWeight: 8.5 Kg Length: 25 cm Width: 31.5 cm Height: 17 cm Width of roller: 25.5 cm Diam. lower roller: 3.5 cm Diam. upper roller: 3.5 cm Metal plate: 26.8 x 42 x 0.3 cmMaximum board or lino thickness: 1.7cmFOME 3mm Felt Mats available here, which you will need to print your plates successfully.Read our series of blog posts about setting up and using the Fome School Etching Press.Other Fome Presses available here.

A biodegradable Vegetable Cleaning Agent for plates, rollers and tools. Protective gloves should during use. Soap and water can be used to finish to cleaning process. This product cannot be used as a dilutant for paints and inks.

This tool is used to prepare metal plates for mezzotints. By repeatedly working the tool over the surface of the plate in a rocking motion, the printmaker can create a smooth carpet of burrs, which will hold ink and show up as a dark area when the plate is printed. This rough surface can then be smoothed with a scraper or burnisher, which will lighten the print in those areas.EC Lyons rockers are known world wide as the finest mezzotint rockers available. Lyons rockers have handles of stained birch and a tool surface of high carbon tool steel. The density of teeth for a rocker is measured in LPI or 'tooth count', a measure of the number of lines per inch on the cutting face of the tool. This is a fine gauge rocker with a 1.5 inch blade and a tooth count of 65.Please take care when using this tool near the edge of your plates, as unless you have bevelled the edge of the plate it is possible that the tool may slip off or be damaged by the sharp edge.

This tool is used to prepare metal plates for mezzotints. By repeatedly working the tool over the surface of the plate in a rocking motion, the printmaker can create a smooth carpet of burrs, which will hold ink and show up as a dark area when the plate is printed. This rough surface can then be smoothed with a scraper or burnisher, which will lighten the print in those areas.EC Lyons rockers are known world wide as the finest mezzotint rockers available. Lyons rockers have handles of stained birch and a tool surface of high carbon tool steel. The density of teeth for a rocker is measured in LPI or 'tooth count', a measure of the number of lines per inch on the cutting face of the tool. This is a fine gauge rocker with a 1.5 inch blade and a tooth count of 100.Please take care when using this tool near the edge of your plates, as unless you have bevelled the edge of the plate it is possible that the tool may slip off or be damaged by the sharp edge.

Lozenge Gravers are used by wood engravers and copper engravers. The face of the tool is lozenge-shaped and will cut a line deeper than it is wide.

This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge.

Please note, engraving tools are known by different names in the U.K. and the United States. Lozenge Gravers are known as 'Lozenge Burins' in the U.S.A.

Square Gravers are used by wood engravers and copper engravers. The face of the tool is square-shaped and will cut a line as deep as it is wide. This is a fine Square Graver (#1).Copper engravers use Square Gravers to create incisions on the surface of metal plates, which will hold ink during the printing process. The lines thus show up as black in the final print.

This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge.

Please note, engraving tools are known by different names in the U.K. and the United States. Square Gravers are known as 'Square Burins' in the U.S.A.

This double-ended scribe can be used in etching or drypoint processes. It has a cork handle for comfort during use.If this tool is used to add detail or tone directly to the metal plate (a technique known as 'drypoint'), it will inscribe a line with a slight burr, which will print a blurred, indistinct line. This effect can be controlled by manipulating the angle at which the point meets the plate.This tool is made of high-carbon steel, and is designed to be resharpened periodically.

Wood engravers use Round Scorpers to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these incisions do not receive ink, and therefore show up white in the final print.This is a medium Round Scorper (#56), used to draw very thick, bold lines. Because the tip of a Scorper is flat, rather than pointed (as Spitstickers and Gravers are), scorpers of larger sizes are used to clear large areas of woodblocks (often round the edge of the design, or at the corners of a block) so that they will not print.Above a certain point, Round Scorpers have strait sides, which means that they will cut a line of a constant width if fully engaged in the wood. However, because the tip of the tool is shaped like a capital U, lines cut with it will have rounded ends.Scorpers are also useful when lightening areas of a print by stippling: repeatedly pecking at the woodblock with the tip of the tool, so that the surface bears a carpet of tiny incisions. Because of the U-shaped tip of this tool, it is perfect for creating large round dots.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the U.K. and the United States. Round Scorpers are known as 'Round Gravers' in the U.S.A.

Wood engravers use Round Scorpers to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these incisions do not receive ink, and therefore show up white in the final print.This is a medium-fine Round Scorper (#53), used to draw thick, bold lines. Above a certain point, Round Scorpers have strait sides, which means that they will cut a line of a constant width if fully engaged in the wood. However, because the tip of the tool is shaped like a capital U, lines cut with it will have rounded ends.Scorpers are also useful when lightening areas of a print by stippling: repeatedly pecking at the woodblock with the tip of the tool, so that the surface bears a carpet of tiny incisions. Because of the U-shaped tip of this tool, it is perfect for creating round dots.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the U.K. and the United States. Round Scorpers are known as 'Round Gravers' in the U.S.A.

Wood engravers use Square Scorpers to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these incisions do not receive ink, and therefore show up white in the final print. Because the tip of a Scorper is flat, rather than pointed (as Spitstickers and Gravers are), scorpers of larger sizes are used to clear large areas of woodblocks (often round the edge of the design, or at the corners of a block) so that they will not print.This is a medium-fine Square Scorper (#39). It has strait sides, which means that it will cut a line of a constant width. Because the tip of the cutting face is completely flat, lines cut with this tool will begin and end abruptly, with a square edge. They will not swell or taper, like lines made with a spitsticker or a graver might; nor will they be rounded at the ends, like cuts made with a Round Scorper.Scorpers are often used to lighten areas of a print by stippling: repeatedly pecking at the woodblock with the tip of the tool, so that the surface bears a carpet of tiny incisions. This tool will create large, angular, squarish dots; for rounded dots, you will need a Round Scorper.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the U.K. and the United States. Square Scorpers are known as 'Flat Gravers' in the U.S.A.

Wood engravers use Square Scorpers to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these incisions do not receive ink, and therefore show up white in the final print.This is a fine Square Scorper (#36). It has strait sides, which means that it will cut a line of a constant width. Because the tip of the cutting face is completely flat, lines cut with this tool will begin and end abruptly, with a square edge. They will not swell or taper, like lines made with a spitsticker or a graver might; nor will they be rounded at the ends, like cuts made with a Round Scorper.Scorpers are often used to lighten areas of a print by stippling: repeatedly pecking at the woodblock with the tip of the tool, so that the surface bears a carpet of tiny incisions. This tool will create angular, squarish dots; for rounded dots, you will need a Round Scorper.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the U.K. and the United States. Square Scorpers are known as 'Flat Gravers' in the U.S.A.

Wood engravers use Tint Tools to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these recessed incisions do not receive ink. They therefore show up white in the final print.This is a medium Tint Tool (#5), designed for cutting straight lines of a constant width. The trade engravers of the Nineteenth century referred to a series of parallel lines as a 'tint'. They used tints to depict colour and form; by varying the width and spacing of the lines that made up their tints, they were able to attain a sophisticated range of mid-tones, between the white of the paper and the black of the ink.This tool is not designed to cut curves; use a Graver or (preferably) a Spitsticker for that. The shank of the tool may be damaged if you force it to make corners.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the UK and the United States. Tint Tools are known as 'Angle Tints' or 'Angle Tint Tools' in the US.

Wood engravers use Tint Tools to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these recessed incisions do not receive ink. They therefore show up white in the final print.This is a medium-fine Tint Tool (#3), designed for cutting straight lines of a constant width. The trade engravers of the Nineteenth century referred to a series of parallel lines as a 'tint'. They used tints to depict colour and form; by varying the width and spacing of the lines that made up their tints, they were able to attain a sophisticated range of mid-tones, between the white of the paper and the black of the ink.This tool is not designed to cut curves; use a Graver or (preferably) a Spitsticker for that. The shank of the tool may be damaged if you force it to make corners.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the UK and the United States. Tint Tools are known as 'Angle Tints' or 'Angle Tint Tools' in the US.

Wood engravers use Tint Tools to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these recessed incisions do not receive ink. They therefore show up white in the final print.This is a fine Tint Tool (#1), designed for cutting straight lines of a constant width. The trade engravers of the Nineteenth century referred to a series of parallel lines as a 'tint'. They used tints to depict colour and form; by varying the width and spacing of the lines that made up their tints, they were able to attain a sophisticated range of mid-tones, between the white of the paper and the black of the ink.This tool is not designed to cut curves; use a Graver or (preferably) a Spitsticker for that. The shank of the tool may be damaged if you force it to make corners.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the UK and the United States. Tint Tools are known as 'Angle Tints' or 'Angle Tint Tools' in the USA.

Square Gravers are used by wood engravers and copper engravers. The face of the tool is square-shaped and will cut a line as deep as it is wide. This is a fine Square Graver (#1).Copper engravers use Square Gravers to create incisions on the surface of metal plates, which will hold ink during the printing process. The lines thus show up as black in the final print.

This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge.

Please note, engraving tools are known by different names in the U.K. and the United States. Square Gravers are known as 'Square Burins' in the U.S.A.

E.C. Lyons Roulettes are designed to be used in intaglio printmaking processes. When the rotating drum at the head of the tool is pushed over the plate, it stipples the ground with dots or lines. Acid will bite through these small impressions, creating dimples in the surface of the metal, which will then hold ink and appear darker in the finished print.The density of lines or dots an engraving roulette will produce is expressed in its DPI rating. A higher DPI indicates the lines or dots made by a roulette as it passes over the face of the plate are closer together. This is a medium gauge line roulette of 85 DPI.

E.C. Lyons Roulettes are designed to be used in intaglio printmaking processes. When the rotating drum at the head of the tool is pushed over the plate, it stipples the surface with dots or lines. These small impressions will hold ink and appear darker in the finished print.The density of lines or dots an engraving roulette will produce is expressed in its DPI rating. A higher DPI indicates the lines or dots made by a roulette as it passes over the face of the plate are closer together. This is a fine gauge line roulette of 100 DPI.

This tool is used to prepare metal plates for mezzotints. By repeatedly working the tool over the surface of the plate in a rocking motion, the printmaker can create a smooth carpet of burrs, which will hold ink and show up as a dark area when the plate is printed. This rough surface can then be smoothed with a scraper or burnisher, which will lighten the print in those areas.EC Lyons rockers are known world wide as the finest mezzotint rockers available. Lyons rockers have handles of stained birch and a tool surface of high carbon tool steel. The density of teeth for a rocker is measured in LPI or 'tooth count', a measure of the number of lines per inch on the cutting face of the tool. This is a fine gauge rocker with a 4 inch blade and a tooth count of 100.Please take care when using this tool near the edge of your plates, as unless you have bevelled the edge of the plate it is possible that the tool may slip off or be damaged by the sharp edge.

This tool is used to prepare metal plates for mezzotints. By repeatedly working the tool over the surface of the plate in a rocking motion, the printmaker can create a smooth carpet of burrs, which will hold ink and show up as a dark area when the plate is printed. This rough surface can then be smoothed with a scraper or burnisher, which will lighten the print in those areas.EC Lyons rockers are known world wide as the finest mezzotint rockers available. Lyons rockers have handles of stained birch and a tool surface of high carbon tool steel. The density of teeth for a rocker is measured in LPI or 'tooth count', a measure of the number of lines per inch on the cutting face of the tool. This is a fine gauge rocker with a 2.5 inch blade and a tooth count of 65.Please take care when using this tool near the edge of your plates, as unless you have bevelled the edge of the plate it is possible that the tool may slip off or be damaged by the sharp edge.

This tool is used to prepare metal plates for mezzotints. By repeatedly working the tool over the surface of the plate in a rocking motion, the printmaker can create a smooth carpet of burrs, which will hold ink and show up as a dark area when the plate is printed. This rough surface can then be smoothed with a scraper or burnisher, which will lighten the print in those areas.EC Lyons rockers are known world wide as the finest mezzotint rockers available. Lyons rockers have handles of stained birch and a tool surface of high carbon tool steel. The density of teeth for a rocker is measured in LPI or 'tooth count', a measure of the number of lines per inch on the cutting face of the tool. This is a fine gauge rocker with a 2.5 inch blade and a tooth count of 100.Please take care when using this tool near the edge of your plates, as unless you have bevelled the edge of the plate it is possible that the tool may slip off or be damaged by the sharp edge.