Japanese synthetic waterstones and slipstones for sharpening lino and woodcut tools of all types.

A fine, 4000 grit multiform synthetic waterstone from Japan. On one edge the curved radius changes from 13mm to 3mm over its length. The opposite edge is tapered at an angle of about 40° making it ideal for sharpening the inside of V tools. The overall design allows the sharpening of a wide variety of tools from flat and wide to small narrow gouges and all V tools.

The 1000 grit can be described as a medium stone and is used to sharpen to an almost perfect cutting edge. The 4000 grit or fine stone is used for the final hone and polish and will leave the tool ready for use. Before use the stones will need to be soaked in water for 10 to 15 minutes. After use the stones are best air dried and wrapped in a soft cloth for storage.

A set of 6 markers with organic, solvent based, lacquer contents.

Contents Include:
6 x Permanent Wood Markers

1 x Spruce

1 x Oak

1 x Mahogany Red

1 x Mahogany

1 x Larch

1 x Beech

Japanese synthetic waterstones and slipstones for sharpening lino and woodcut tools of all types.

A medium, 1000 grit multiform synthetic waterstone from Japan. On one edge the curved radius changes from 13mm to 3mm over its length. The opposite edge is tapered at an angle of about 40° making it ideal for sharpening the inside of V tools. The overall design allows the sharpening of a wide variety of tools from flat and wide to small narrow gouges and all V tools.

The 1000 grit can be described as a medium stone and is used to sharpen to an almost perfect cutting edge. The 4000 grit or fine stone is used for the final hone and polish and will leave the tool ready for use. Before use the stones will need to be soaked in water for 10 to 15 minutes. After use the stones are best air dried and wrapped in a soft cloth for storage.

A beveling tool ideal for creating beveled (rounded off or sloping) edges. Unlike most other beveling or chamfering tools, this beveler is extendable to allow for different thickness of material. This beveler has a red varnished beechwood handle, a metal head and steel cutting blades. Please Note: To cut the perfect bevel, we strongly advise securing your plastic or metal plate on a table or workbench before cutting.

Lozenge Gravers are used by wood engravers and copper engravers. The face of the tool is lozenge-shaped and will cut a line deeper than it is wide.

This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge.

Please note, engraving tools are known by different names in the U.K. and the United States. Lozenge Gravers are known as 'Lozenge Burins' in the U.S.A.

Lozenge Gravers are used by wood engravers and copper engravers. The face of the tool is lozenge-shaped and will cut a line deeper than it is wide.

This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge.

Please note, engraving tools are known by different names in the U.K. and the United States. Lozenge Gravers are known as 'Lozenge Burins' in the U.S.A.

Familiar to all Japanese students, these economical introductory cutters offer good quality steel blades that can be re-sharpened. The tools can be used for all types of lino and work very well for cutting woodblocks.

The set of five consists of one outline knife, one flat clearing chisel, two U gouges and one V cutter. There are some guidelines on the box with diagrams of how to hold the tools.

Wood engravers use Spitstickers to create incisions on the surface of woodblocks. As woodblocks are inked with a roller, these incisions do not receive ink. They therefore show up white in the final print.This is a fine Spitsticker (#1). The tip of the tool is pointed, but the sides are curved. This makes it possible to draw long, fluid lines which twist and curve gracefully, and which taper away rather than terminating in a flat or round edge (like lines drawn with a scorper). Used lightly, a spitsticker will score a thin line; the line will swell if the tool is engaged further into the wood.This tool was made from high carbon tool steel in the United States by E.C. Lyons. It is supplied factory-sharp, but it has not been honed to a fine edge. Please note, engraving tools are known by different names in the U.K. and the United States. Spitstickers are known as 'Elliptic Tints' or 'Elliptic Tint Tools' in the U.S.A.

When metal plates are engraved for intaglio printmaking, small ridges of cut-away metal called 'burrs' will be left either side of each linear incision. This scraper has a triangular blade, and is designed to be used during intaglio printmaking processes, to scrape away burrs thrown up during the engraving process without damaging the plate. Its sharp face can also be used to scrape and lower the plate surface.It has a wooden handle, and is made of high carbon steel.

The wood of choice for carvers, this sturdy substrate is ready to make miracles with Cricut Maker®. Denser than balsa wood, basswood has a smooth, even wood grain – an ideal surface for clean cuts to craft models, toys, puzzles, or even small gift crates. It can be painted and stained easily without having to seal it first. For use with Cricut Maker and Knife Blade only.

The TechnoArt Wood Cutter Set includes 6 different metal blades for different shapes.

Each Blade features a long narrow handle that is comfortable for most hands with blades made from high-quality tool metal.

The TechnoArt Wood Cutter Set includes 12 different metal blades for different shapes.

Each Blade features a long narrow handle that is comfortable for most hands with blades made from high-quality tool metal.