Ultra-fast and extremely strong liquid super glue in 3 single mini tubes. The originally sealed tubes always provide the right dose of perfect, ready-to-use glue quality. Packed in a solid storage box. The liquid adhesive flows into smallest corners and joints. Dishwasher proof and water resistant.

Suitable for:
Ideal for small-area bonds.
Glues almost all solid and flexible materials like many plastics (such as rigid PVC, ABS, PS, Plexiglas®, polycarbonate (Makrolon®), and phenolic resins (Bakelite®)), porcelain, ceramics, leather, metal, wood, cork, felt, cloth (check suitability first), and rubber.
Only partly suitable for glass (over a certain period of time the bond becomes brittle, causing it to weaken).

Not suitable for: PE, PP, silicone resins, PTFE, Styrofoam®, fabrics and leather clothing.

Working conditions: Do not use at temperatures below +10 °C. The glue responds best to an air humidity level of 50-70 %.
Surface requirements: Surfaces to be glued must be clean, dry, and free of dust and grease, and must fit exactly.
Preliminary surface treatment: Any dust, oil, grease, wax or separating agent should be thoroughly removed from the surfaces to be stuck together. The best way to achieve this is to rub the parts a number of times with appropriate solvents, such as acetone (if suitable for the material – check first!). For metals and metal alloys it is usually sufficient to roughen the surface using emery paper or by grinding or brushing.

Directions For Use
1. To pierce the membrane, turn the cap clockwise firmly onto the tube. Tip: do not press the tube while piercing.
2. Unscrew the cap to reveal the applicator. Apply the adhesive directly from the tube, using the nozzle, as thinly as possible onto one side (too much glue slows down the curing process significantly).
3. Press parts together immediately.

After use (if tube not yet empty), clean nozzle with a dry tissue and replace cap.

Advice
When glueing at low humidity, curing time can be shortened by briefly breathing onto one of the parts to be assembled. The best glueing results are reached at room temperature.

Points of attention
Contains cyanoacrylate. Bonds skin and eyelids together in seconds.
If product comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice.
In case of contact with skin, glue can be dissolved by soaking in warm soapy water.
Then apply a skin cream.
May cause respiratory irritation.
Avoid breathing vapours.
Keep out of the reach of children.
Stains/residue: Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue but very slowly (check suitability first).

Storage conditions: Store in a dry, cool, frost-free place. Storage below +5 °C (in refrigerator) ensures maximum shelf life.

Non-toxic and solvent free. Safe, clean and washable. Ideal for paper and board. Perfect for school projects.

Non-toxic and solvent free. Safe, clean and washable. Ideal for paper and board. Perfect for school projects.

CROXLEY CREATE 36G GLUE STICKS PACK 3

Super-strong universal contact adhesive based on neoprene rubber. For innumerable repair and DIY jobs that require immediate bonding. Extremely suitable for materials under strain. Moisture and frost proof. Resistant to temperatures between -15 °C and +70 °C.

Suitable for:
Ideally suited for surface bonding or laminating of many materials that require immediate bonding, loading or processing.
Bonds wood, board, veneer, plastic and metal panel boards (HPL, Formica®, for example), (foam) rubber, leather, cork, canvas, linoleum and polyether foam (sound insulation), among other things, to itself as well as to many other surfaces.
Also for repairing shoes, bags, toys and carpets, or for doing (hobby) handicraft work.

Not suitable for: Polystyrene foam (Tempex®), PE, PP, PTFE and vinyl.

Working conditions: Use adhesive and parts to be bonded at room temperature only. The relative humidity must be below 65 %. This is to avoid formation of bubbles in the final product. Once attached, adjustment is no longer possible. Always test on an (inconspicuous) part of the surface first.
Surface requirements: Surfaces must be dry, clean, dust- and grease-free and a good fit.
Preliminary surface treatment: Clean and degrease the surfaces to be bonded for optimal results.
Tools: Use a solid brush or fine-toothed (1 mm) glue spreader to cover large surfaces. Use a roller or rubber mallet to join the materials firmly.
Preparation of product: Stir well before use. Should preferably not be diluted
Coverage: 2 - 2.5 m²/litre, applied on both sides, depending on the nature of the materials to be bonded.

Directions For Use
Parts must be clean, dry and free of grease.
Coat both substrates completely.
Allow to dry for a minimum of 10 - 40 minutes.
In case of porous materials, apply a second coat and let dry.
Then join parts and roll or tap firmly (with a rubber mallet).

Points of attention
For optimum results, both the adhesive and the parts to be bonded must be at room temperature (definitely do not use below +10 °C).
The final bonding strength depends on the pressure applied.
Therefore, press as firmly as possible across the entire surface.
Should the adhesive joint between porous materials be exposed to long-lasting contact with water, the adhesive may detach from the wet surface.
Stains/residue: Remove fresh adhesive residue immediately with Acetone. Dried adhesive residue can only be removed mechanically or with a paint remover (test first).

Storage conditions: Store properly closed in a cool and frost-free place. Shelf life is a minimum 24 months.

Clear glue that dries clear.

PATTEX contact adhesives are heat resistant, flexible ,spread easily and bond fast. It is suitable for use on most materials and is Toluene free , creating a safer working environment.

A ready to use wood glue for most kinds of woods, for assembling and repair jobs. The bonds produced are slightly flexible and have a clear glue line. Suitable for DIY, hobby, craft and school projects. Dries fast, clear and strong.

Dala Paper Glue is a non-toxic, clear, liquid glue that is suitable for all school and office paper and cardstock projects. Can be further diluted with water for paper mache and similar projects.

Dala Craft Glue is a liquid, white glue that dries slightly opaque. It is an acid free, non-toxic multi-purpose adhesive that adheres to most surfaces. Ideal for crafting and scrapbooking.

PATTEX Liquid Super Glue comes in a small easy to use 3g tube. It can be used on a variety of different materials including items that come into contact with water. It is also dishwasher safe. Not recommended for applications where there is going to be movement, expansion or contraction of the bond item.

Yamayo Superglue Card of 12 (2.5g)

PATTEX 100% Gel has the ability to repair multi materials indoors and outdoors. It is suitable for use on metal, plaster, glass, wood, leather, textile and much more. It can also be used for various arts and crafts projects as it is adjustable and dries clear. Solvent-free, no shrinkage, has 1-component, moisture-curing.

Pattex Super Gel carded 3g carded

High quality, moisture resistant (EN 204 D2) white wood adhesive for internal use. Dries transparent. Stronger than wood. For bonding and laminating of practically all hard, soft and exotic types of wood.

Suitable for:
For moisture resistant joining and laminating of practically all hard, soft and exotic types of wood.
Well-fitting, non-load bearing wooden structures using, for example, finger joints, dovetail joints, mortise and tenon joints, dowels and springs.
Indoor applications such as doors and furniture in, for example, living rooms and offices.
Surface bonding wood, hard and softboard, chipboard, multiplex plywood, MDF, paper, cardboard and hardboard.
Laminating veneer and hard plastic sheet (HPL, Formica, Duropal, Resopal) on a wooden surface.

EN 204 D2: Interior spaces in which increased relative humidity occurs occasionally and for a short time, whereby the level of wood humidity remains below 18%.

Working conditions: The ambient temperature, the adhesive and the materials to be bonded should be no less than +5°C. Relative humidity of up to 65%. Level of wood humidity between 8% and 12%.
Surface requirements: The surfaces to be bonded need to be clean, dry and free of dust. Ensure a well-fitting joint.
Preliminary surface treatment: Degrease oily types of wood with thinner.

Tools: Fine-toothed glue spreader (1 mm), brush or roller, clamp or press.
Dilute: Dilute only with water.
Coverage: 2-4 m²/kg, applied on both sides, depending on the nature of the materials.

Directions For Use:
Apply the adhesive with a brush or some other tool in an even and thin layer on one or both parts.
Let penetrate for a few minutes, assemble the parts within 10 minutes and clamp or press for 4-15 minutes.
The desired pressure is 2-5 kg/cm².
Stains/residue: Remove adhesive residues immediately with water. Dry adhesive residue can only be removed mechanically.

Storage conditions: Close container properly and store in a dry, cool and frost-free place.

White Glue (250ml)

PATTEX contact adhesives are heat resistant, flexible ,spread easily and bond fast. It is suitable for use on most materials and is Toluene free , creating a safer working environment.