THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.


PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.


NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.

APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.

APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

KIT INCLUDES:
•1 x 1 LTR POWR RUBBER SEAL
•1 x 2M POWR WATERPROOFING MEMBRANE
•1 x APPLICATION BRUSH

THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.


PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.


NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.

APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.

APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

KIT INCLUDES:
•1 x 1 LTR POWR RUBBER SEAL
•1 x 2M POWR WATERPROOFING MEMBRANE
•1 x APPLICATION BRUSH

THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.



PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.



NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.



PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.



NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.


PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.


NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.

APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.

APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

KIT INCLUDES:
•1 x 1 LTR POWR RUBBER SEAL
•1 x 2M POWR WATERPROOFING MEMBRANE
•1 x APPLICATION BRUSH

THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.



PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.



NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

POWR Spray Paint presents a wide spectrum of brilliant colours for paint jobs with a professional finish. The advanced formulation provides outstanding resistance to peeling, cracking, chipping and colour fading caused by all weather conditions.

Warnings:
Caution: Flammable - Keep away from heat sources and open flames.
Store Below 50 degrees
Harmful vapours - Use in a well-ventilated area
Keep away from Children
Do not pierce can

POWR Spray Paint presents a wide spectrum of brilliant colours for paint jobs with a professional finish. The advanced formulation provides outstanding resistance to peeling, cracking, chipping and colour fading caused by all weather conditions.

Warnings:
Caution: Flammable - Keep away from heat sources and open flames.
Store Below 50 degrees
Harmful vapours - Use in a well-ventilated area
Keep away from Children
Do not pierce can

POWR Spray Paint presents a wide spectrum of brilliant colours for paint jobs with a professional finish. The advanced formulation provides outstanding resistance to peeling, cracking, chipping and colour fading caused by all weather conditions.

Warnings:
Caution: Flammable - Keep away from heat sources and open flames.
Store Below 50 degrees
Harmful vapours - Use in a well-ventilated area
Keep away from Children
Do not pierce can

Paint Buddy Replacement Sponge Roller. When it looks like your Paint Buddy has seen better days, maybe it is time for a new sponge refill. Please note that this product is not suitable for enamel paint!

Professional quality masking tape. Excellent value for high quality work. Available in ½�, ¾�, 1�, 1.5�, 2�, 3�, 4�. 50 metres in length.

THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.



PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.



NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.



PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.



NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

High Heat Spray Paint is ideal for use on the exterior of braai stands, fireplaces, stoves, automotive parts and so much more.

Low tack paper masking tape. Individually shrink wrapped, 50m rolls. Available in 1�, 1.5� and 2�.

Bulk Pack x 5 Sprayon Paint Black Matt 250ml

Bulk Pack x 5 Sprayon Paint Black Gloss 250ml

The Interior Design Wheel gives home decorators a guide for selecting complementary colours for interior design.The wheel illustrates split complementary, monochromatic, and harmonised colour schemes.Packed in a sleeve for insertion in a three-ring binder.8-1/2“ x 11“ (21.6 x 28 cm).

Introducing the paint buddy, the easy to use non-drip paint roller! In three easy steps, you can start painting without having to worry about any messes and drips.

Thanks to the simplicity of the Paint Buddy, there is less strain and hassle for you to worry about. To make things even better is that you don't have to stress about accidentally knocking over the paint bucket or wasting paint by dripping on the floor, which in turn saves you both time and money!

The Paint Buddy works on all surfaces like wood, concrete, bricks and even rubber.

3 Simple Steps:

Unclip the lid on the side of the paint roller and fill the area with paint.
Snap the lid closed.
Roll on the paint!

Professional quality masking tape. Excellent value for high quality work. Available in ½�, ¾�, 1�, 1.5�, 2�, 3�, 4�. 50 metres in length.

Paint Brush Wooden Handle PVC Bag 3 Pack (50mm)

Professional quality masking tape. Excellent value for high quality work. Available in ½�, ¾�, 1�, 1.5�, 2�, 3�, 4�. 50 metres in length.

Paint-Roller Set Tray Supreme 2 Pack (230mm)

Bulk Pack x 4 Sprayon Spray Paint 250ml Satin Black