Kera is an air drying modelling clay that comes in both white and terracotta brown. The clay can be used for modelling and then hardens slowly over a 24 hour period. To extend the working time of the clay use the product with wet hands. After the clay has hardened, no further modelling is possible.

Not suitable for use by children under the age of 3 years.

A fine and natural modeling clay. Highly malleable, it is recommended for modelling, sculpture and pottery. Fire in a kiln at 980˚C.

A fine and natural modeling clay. Highly malleable, it is recommended for modelling, sculpture and pottery. Fire in a kiln at 980˚C.

A fine and natural modeling clay. Highly malleable, it is recommended for modelling, sculpture and pottery. Fire in a kiln at 980˚C.

A fine and natural modeling clay. Highly malleable, it is recommended for modelling, sculpture and pottery. Fire in a kiln at 980˚C.

Can be used to cover all types of objects, produce masks by applying directly to the skin, make supporting shells for the siligum, alginate or latex moulds.

Can be used to cover all types of objects, 4 x 8 x 300cm produce masks by applying directly to the skin, 8 x 300cm make supporting shells for the siligum, alginate or latex moulds.

Natural red clay, ready for use. Formulated with a synthetic binder hardens without firing in 4 or 5 days. Very malleable, it does not dry with cracks. Can be waterproofed to seal non-food containers. • The non-firing clay can be used in modelling but also for making moulds to cast plaster etc. • The drying can be accelerated by placing the object in a microwave oven for a few minutes. • Preservation: until it has dried, the Gedeo clay can be reused indefinitely if stored in a wet towel inside a tightly closed plastic bag. pdf=Gedeo.pdf Gedeo Product Information

A high quality air dry clay made from a mineral and water based material with a soft fine texture. Form this clay by hand or use press moulds, stamps or cutters.

Jackson’s Air Dry Clay hardens naturally in air without a kiln. This occurs within hours or days depending on size of piece. Water should be added for ease of working. The clay does not contain nylon fibres and so will have minimal dragging when cutting.

Store in the supplied airtight container to prevent drying. Partially dried clay can be made workable again by wrapping in a damp cloth overnight.

Clean with soap and water. May stain clothing or surfaces.

Not suitable for children under 36 months.

Kera is an air drying modelling clay that comes in both white and terracotta brown. The clay can be used for modelling and then hardens slowly over a 24 hour period. To extend the working time of the clay use the product with wet hands. After the clay has hardened, no further modelling is possible.

Not suitable for use by children under the age of 3 years.

Low density plaster rcommended for casting hanging decorations.

Modelling clay tools for finishing and cutting modelling clays. Made of rigid polycarbonate for durability and longevity. Easy to wash.

Modroc is a plaster bandage i.e. a gauze impregnated with Plaster of Paris. Once dipped in water, it can be applied to a surface to make a cast or shape. The plaster will start to set after about 3 minutes.The Modroc will be hard enough to handle after 30 minutes and will develop to full strength overnight. It can be used on its own in a suitable mould, or sculpted around wire or card models. Smaller strips can be cut off with scissors.The Modroc can be decorated and painted with acrylic paints when fully dry.

A high quality air dry clay made from a mineral and water based material with a soft fine texture. Form this clay by hand or use press moulds, stamps or cutters.

Jackson’s Air Dry Clay hardens naturally in air without a kiln. This occurs within hours or days depending on size of piece. Water should be added for ease of working. The clay does not contain nylon fibres and so will have minimal dragging when cutting.

Store in the supplied airtight container to prevent drying. Partially dried clay can be made workable again by wrapping in a damp cloth overnight.

Clean with soap and water. May stain clothing or surfaces.

Not suitable for children under 36 months.

STAEDTLER FIMOair is an air-drying modelling clay. The drying time depends on the thickness of the modelled item. This means you don’t have to harden your modelled items in the oven. In addition, once they have dried, your items will still be extremely break-resistant. You can start finishing pieces as soon as they have dried. FIMOair is available in three varieties that are ideal for creating a range of different items: FIMOair basic, FIMOair natural and FIMOair light.

FIMOair basic – Clay-like results without a kiln
STAEDTLER FIMOair basic modelling clay is available in three colours: white, flesh and terracotta. Items made from this modelling clay have a clay-like appearance. However, the main advantage is that you don’t need a kiln to achieve these results. FIMOair basic simply dries naturally in the air. You can then use corresponding accessories to paint, drill or varnish your items to suit your style.