THE POWR RANGE OF WATERPROOFING PRODUCTS ARE IDEAL FOR THE HARSH SOUTH AFRICAN CLIMATE.

POWR now provides you with all your high quality, eco-friendly, waterproofing products under one trusted brand.

Introducing our dynamic waterproofing range – the ultimate solution to protect your surfaces against moisture, leaks, and water damage. Our range of high-performance waterproofing solutions include POWR Rubber Seal, POWR Bonding Liquid, POWR Membranes and POWR Waterproofing Tapes. They are specially formulated to provide a reliable barrier against the elements, keeping your walls, floors, and structures waterproof and pristine. POWR Waterproofing products that offer both a variety of functional solutions and easy application.



PERFORMANCE BENEFITS:
•Bonds to most construction materials
•Elongates 100% with 95% recovery - Highly stretchable and contracts to its original form.
•Withstands thermal cycling
•Puncture resistant
•Strong UV exposure
•Withstands exposure to industrial chemicals
•Improves lifespan of coated substrates.
•Corrosion control.
•Encapsulation (Asbestos).
•Environmentally Friendly and can be applied were rainwater is harvested.
•Waterproofing that can withstand ponding of water.
•Can be applied to all construction materials
•Spray, paint or roller applied.
•Total ambient temperature application - No heating or propane flame heating required.
•Seals joints and covers fine cracks

PRODUCT USES:

•For all roof types/structures including:
•Fibre cement roof sheets
•Cement roof tiles
•Chromadek
•Zinc Alum and AluZinc
•Exterior trims such as facias, gutters, window sills and cement garden pots

APPLICATION:
•Always Mix POWR Rubber Seal well before use.
•Make sure all substrates are completely clean, sound, dry, and free from any laitance (a white film that forms on the surface of drying concrete), fungus, grease, oil, or loose and flaking particles.
•Do not dilute POWR Rubber Seal (application ready)
•Apply two coats by brush or roller
•A third coat is recommended for coastal areas.
•Determined by the condition, allow approximately an hour drying time between coats.
•Touch dry time is approximately 2 hours in hot dry conditions (25°C)


POWR WATERPROOFING MEMBRANE APPLICATION:
•Apply a generous coat of POWR Rubber Seal.
•Press membrane into wet POWR Rubber Seal surface.
•Apply a generous coat of POWR Rubber Seal over membrane until covered and allow to dry for 90 minutes
•Apply a final coat of POWR Rubber Seal over coated surfaces.


GALVANIZED METAL ROOF SHEETING APPLICATION:
Wash all fungi-infested areas and cracks with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery paint or surface laitance by pressure washing. Prime all rust-affected areas ( if any ) with Triple Red Rust Converter.



NEW METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow to dry for 2-3 hours before overcoating. The area must be overcoated within 24 hours to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal (0.8kg - 1kg / m2)


WEATHERED METAL SURFACES:
Apply one coat of Anti Corrosion Metal Primer to entire surface and allow 2-3 hours drying time before overcoating. The area must be overcoated within 3 days to prevent a loss in adhesion. Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg / m2)


PROBLEMATIC METAL AND BITUMEN SURFACES:
An Acid Metal Etch Primer is advisable to use as a substitute for Anti Corrosion Metal Primer under the following circumstances: Where flaking of factory-coated metal sheeting is observed. Over areas that were coated with bituminous products apply Bitumen Barrier Primer.


METAL AND CHROMADECK ROOF SHEETING:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter. Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply a coat of Anti Corrosion Metal Primer.
•Prime all areas (full primer) and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg /m)


ASBESTOS, NUTEC ROOF SHEETING AND CEMENT TILES:
Wash all fungi-infested areas with a Fungi Wash and leave for 24 hours to react. This will kill spores and limit fungal growth. Remove all loose, flaking and powdery or surface laitance by pressure washing. Prime all rust-affected areas (if any) with Triple Red Rust Converter.
Scour the entire surface with a scouring pad to promote adhesion of the subsequent coatings.
APPLICATION:
•Apply one coat of POWR Bonding Liquid to all areas (full primer), and allow to dry for +- 8 hours.
•Apply two coats of POWR Rubber Seal ( 0.8kg - 1kg/m2)


COVERAGE:
•Coverage will vary depending on the substrates/surface porosity.
•Coverage must be between 0.8kg - 1kg / m2


MAINTENANCE COAT:
To ensure warranty a maintenance coat must be applied every 3 - 4 years

WHAT MAKES IT UNIQUE:
•Spray or brush applied at ambient temperature
•Cures into a seamless membrane
•Excellent Waterproofing
•Corrosion resistance
•Chemical resistance
•Encapsulation


ROOF COVER APPLICATION:
•Waterproofing
•Encapsulating
•Rust Prevention
•Rust Rehabilitation
•Chemical protection

ROOF SURFACES:
•Metal Sheeted Roofs
•Tiled Roofs
•Asbestos / Nutech Roofs
•Concrete Slab Roofs


CLEAN UP:
Clean equipment with warm, soapy water


TRANSPORTING PAINT:
It is important to make sure that your paint products are properly and safely secured upright when transporting them.


SAFETY PRECAUTIONS:
•Keep out of reach of children.
•Read the label before use
•Ensure good ventilation during application and drying.
•In case of skin contact, wash with soap and water or a recognized skin cleaner. Avoid contact with eyes - in case of contact, rinse your eyes immediately with plenty of water and seek medical advice if symptoms persist. If ingested, drink plenty of water/milk. Do not induce vomiting. Seek medical attention.
•Store in a closed container.
•Store in a well-ventilated place.
•Keep cool.
•Dispose of contents/containers by local regulations
•Refer to safety data sheets and technical data sheets for further information

An Annular Hole Cutter TCT 75 x 30mm Weld Shank 31.75mm is a cutting tool designed for creating precise, clean holes in materials like metal. It features a TCT (Tungsten Carbide Tip) for durability and longer tool life, making it ideal for cutting through tough materials. The cutter has a 75mm outer diameter and a 30mm depth of cut, providing the ability to cut deep holes. The Weld Shank with a diameter of 31.75mm allows it to be securely mounted onto a compatible machine for accurate, efficient cutting, particularly in industrial or heavy-duty applications.

The ANNULAR HOLE CUTTER TCT 90 x 30MM with a weld shank of 31.75MM is a high-performance tool designed for precise hole cutting in metal. It features a tungsten carbide-tipped (TCT) construction, ensuring durability and sharpness for cutting through tough materials. The 90mm diameter and 30mm depth of cut allow for efficient and clean hole creation, while the 31.75mm weld shank ensures compatibility with a variety of drilling machines. This cutter is ideal for industrial applications that require precise, deep holes, such as in construction, manufacturing, or repair tasks.

The Annular Hole Cutter TCT 70 x 30mm Weld Shank 19.05mm is a specialized cutting tool used for drilling larger, precise holes in tough materials, such as metal, steel, and other hard substrates.

TCT (Tungsten Carbide-Tipped) refers to the cutting edge material, which is made of tungsten carbide, a highly durable and hard material. TCT ensures that the cutter can withstand the wear and heat associated with cutting through tough materials.
70mm is the diameter of the hole the cutter is designed to create, meaning it will drill holes 70 millimeters wide.
30mm is the cutting depth of the cutter, indicating that it can drill holes up to 30 millimeters deep into the material.
Weld Shank refers to the shank type of the cutter, meaning the shank is welded to the cutting tool. This type of shank is often used in industrial applications for increased strength and stability during heavy-duty use.
19.05mm refers to the shank diameter (the size of the hole at the bottom of the cutter), which is 19.05 millimeters (or 3/4 inch). This specific size ensures compatibility with machines that accept this size of cutter.
Annular hole cutters are particularly useful for cutting clean, precise holes in metal without the need for a full drill bit. They remove a ring of material from the center, leaving a clean, accurate hole with minimal heat buildup. This cutter is often used in industrial applications, steelworking, and metal fabrication where large, deep holes are needed.

The Annular Hole Cutter TCT 102 x 30mm Weld Shank 31.75mm is a cutting tool designed for creating precise, large holes in metal materials, typically used with a magnetic drill. Here are the key features:

102mm Outer Diameter: The cutter has an outer diameter of 102mm, ideal for drilling large holes in thick metal plates and structures.
30mm Cutting Depth: With a 30mm cutting depth, it is suitable for creating holes that are deep enough to accommodate larger fasteners or bolts.
TCT (Tungsten Carbide Tipped): The TCT cutting edges provide exceptional durability and wear resistance, allowing the tool to cut through tough materials like steel, cast iron, and other hard metals.
Weld Shank 31.75mm: The 31.75mm weld shank is designed to fit most magnetic drills and ensures secure attachment to the drill, providing stability and reducing vibration during the cutting process.
This Annular Hole Cutter is commonly used in metalworking, construction, and engineering industries for creating precise holes with minimal material wastage, particularly in applications that require large, deep holes for structural or mechanical purposes. The TCT material ensures longevity and sharpness throughout its use.

The Annular Hole Cutter TCT (90 x 55mm) with a Weld Shank (31.75mm) is designed for creating precise, clean holes in metal and other tough materials. The TCT (Tungsten Carbide Tips) provide exceptional durability and performance, making it ideal for heavy-duty industrial applications such as metalworking and fabrication. With a 90mm cutting diameter and 55mm cutting depth, it is suited for larger holes and deeper cuts. The 31.75mm weld shank ensures a secure fit with compatible machines, allowing for efficient and accurate hole cutting.

The ANNULAR HOLE CUTTER TCT 83 x 30MM with a weld shank of 31.75MM is a high-performance cutting tool designed for making precise holes in tough materials such as metal, concrete, and masonry. The cutter is made with tungsten carbide tips (TCT), ensuring long-lasting sharpness and durability for efficient cutting. With an 83mm diameter and a 30mm cutting depth, this tool is ideal for applications where larger, deeper holes are required. The 31.75mm weld shank ensures compatibility with a wide range of drilling machines, making it a versatile choice for industrial, construction, and mechanical work.

King Tony Nut Setter Magnetic (2 Pack) (3/8" x 65mm)

The Service Kit 100mm Jaws/Worm/Handle for TCV13100 is a replacement parts kit designed for the TCV13100 model (likely a type of clamp or vice). This kit includes the 100mm jaws, worm gear, and handle, which are essential components for maintaining the functionality and performance of the tool. The 100mm jaws ensure a strong grip, while the worm gear and handle allow for precise adjustment and smooth operation. Ideal for those needing to replace worn or damaged parts, this service kit ensures that your TCV13100 tool continues to perform at its best, making it perfect for workshops, maintenance, and repair tasks.

The Service Kit 175mm Jaws/Worm/Handle for TCV12175 is a replacement or maintenance kit designed for the TCV12175 tool or equipment model. Here's a breakdown of the components included in the kit:

175mm Jaws: These are the clamping jaws used in the tool, typically responsible for gripping or securing materials. The 175mm size refers to the length or opening of the jaws, ensuring they fit properly with the equipment for precise operations.

Worm: The worm is a component of the gear system that transfers motion and force within the tool. It helps with precise adjustments or settings for the tool's movement, enabling efficient operation.

Handle: The handle allows the user to operate the tool, providing control during use. This handle may be designed for comfort and ease of handling, especially during longer tasks.

This service kit is intended for maintenance or repairs of the TCV12175 model, ensuring continued reliable performance by replacing worn or damaged components, such as the jaws, worm, and handle.

Kaufmann 2.5 Metre Chain Hoist - 1500kg

The Impact Driver Insert Bits 4pc (5/16") set includes four high-quality, durable bits designed for use with impact drivers. The set includes the following bit types:

PH2 (Phillips #2)
PH3 (Phillips #3)
SL8mm (Slotted 8mm)
SL10mm (Slotted 10mm)
Each bit is engineered to withstand the high-torque force of impact drivers, making them ideal for heavy-duty applications like driving screws into wood, metal, or other materials. The 5/16" size ensures a secure fit and prevents slipping during use. These bits are perfect for professional and DIY users looking for versatile, reliable bits for various fastening tasks.

The Pica Big Dry Permanent Lead Refill 12pc Set Assorted Colors is a set of high-quality, refill leads designed for use with the Pica Big Dry Automatic Pen. The set includes 12 pieces of lead in various vibrant colors, providing versatility for marking and drawing on a range of surfaces, including wood, metal, plastic, and stone. The permanent lead ensures that your markings are durable and resistant to fading, making it ideal for construction, carpentry, and other professional applications. The leads are designed to be long-lasting and are compatible with the Pica Big Dry pen, offering a smooth and consistent marking experience.

Bulk Pack x 2 Flange Black FF Weld On Table D 100mm

The Force X SDS-Plus Set KM7, 7 pieces, includes a selection of high-quality drill bits designed for use with SDS-Plus rotary hammer drills. This set features drill bits in various sizes, specifically:

5.0mm, 6.0mm, and 8.0mm in 110mm length
6.0mm, 8.0mm, and 10mm in 110mm length
These bits are ideal for drilling into concrete, masonry, and other tough materials, offering precision and durability. The SDS-Plus shank ensures quick and secure bit changes, improving efficiency during use. This set is perfect for both professional contractors and DIY enthusiasts needing a versatile set of drill bits for heavy-duty tasks.

Bulk Pack x 2 Large Strainer & Plug Sink Waste - 90mm

Samite Flush Adjust Distribution Board - 16Mod

Bulk Pack x 20 Washer Tapered 32mm Hole Beta (Lied)

Sleeve Lock High Strength for Large Diameter Cylindrical Parts (Green) is a specialized adhesive designed to secure large-diameter cylindrical components in place, such as shafts, sleeves, and bearings. This high-strength formula provides a strong, durable bond that prevents parts from slipping, shifting, or loosening over time. The green color typically indicates a stronger bond, suitable for heavy-duty or high-stress applications. It ensures a firm hold on larger components, making it ideal for machinery, automotive, and industrial uses where a more robust locking solution is required, while still allowing for disassembly when needed.

Bulk Pack x 7 Grinding Techniques - Superflex - Masonry Cutting Disc - 23cm

Bulk Pack x 4 Pratley Wonda Fix Car - 30ML

Torrenti Y Brass Strainer - 50mm

Kaufmann PPE Day Vest - Glow Lime Medium

Alcolin - 300ml Silicone Sealant - Grey

Bulk Pack x 50 Washer Tap Rubber 15mm Light Pattern